Solid floor systems

The Continal® screed system - Quick and easy, familiar to the installer and cost effective.

The most common method of fitting underfloor heating, suitable for new builds and renovations where a new screed floor is being laid. Using our trusted SUPERflex™-16 or AluPlas®-16 UFH pipe and our EasyFix™ fitting systems.

Learn more

Suspended floor systems

OneBoard® structural system

OneBoard® – Structural system that can be laid directly on joists. Saving you time and money on site.

The system is ideal for both new build and retrofit installations. With minimum floor build height. The composite chipboard panel with heat dissipation foil offers excellent output and response, and is suitable for all heat sources.

Learn more

AluPlate™ fit-from-above

AluPlate™ fit-from-above – Quick and easy to install, with no increase in the finished floor height.

The AluPlate™ fit-from-above system clips our 16mm pipe in position, ensuring excellent surface contact with the pipe and the floor deck. This maximises heat transfer and is covered with the load-bearing floor deck, which can then be covered with your choice of flooring.

The system is incorporated within the floor construction and therefore does not affect the finished floor height. The AluPlate™ fit-from-above system is covered with the load-bearing floor deck, which can then be covered with your choice of flooring.

Learn more

AluPlate™ fit-from-below

AluPlate™ fit-from-below - Allows the system to be installed from below after the floor has been laid. This could be either during construction or as part of a renovation where access from below is available.

AluPlate™ fit-from-below plates are versatile and allow for all joist spacings, letting you install single, double, and triple pipe runs, maximising design and performance.

Learn more

PUG / dry mix

The PUG / dry mix - Uses readily available and familiar materials, making it a simple and cost-effective method of maximising the heat output.

The system is installed from above, and can either be laid within the floor construction, or between battens above an existing floor where height permits.

Learn more

Overfloor systems

TileFix®-18 / TileFix®-25

TileFix® – The only system you can tile directly onto, with a low-profile from just 18mm.

TileFix® fast-response, high compressive strength system, is ideal for renovation, new build, whole house and single room projects. Designed to accept direct tiling with a standard tile adhesive and is typically installed over existing solid or timber deck floors.

Learn more

UltraSlim™-15

UltraSlim™-15 – Ultra low-profile system at just 15mm thin. Fast response, suitable for all heat sources and is ideal for renovation and new build.

UltraSlim™-15 combines a high strength MDF base, and heat dissipation layer to maximise output and temperature variance.

Learn more

SlimFix®-18 / SlimFix®-25

SlimFix® – Low-profile system from only 18mm thin with built-in return panels. Making installation quick and easy. Ideal for renovation, new build, whole house, or single room projects.

SlimFix® is a high-compressive strength composite panel with a heat-dissipation layer, which maximises heat output and temperature variance.

Learn more

SlimFix®-TR

SlimFix®-TR is a composite system panel with built-in returns which is ideal for larger, whole-house projects as its quick and easy to install.

Suitable for both renovation and new build projects, and can be installed over existing solid or timber deck floors, or as part of a floating floor construction.

Learn more

ThermoDEK™-18 system

ThermoDEK™-18 - Super-thin, highly efficient overfloor system, with a solid gypsum dry-screed panel at its heart.

It provides a high-output, low-profile, high-strength solution, which can typically be laid over existing floors.

Suitable for low and high-temperature systems, it incorporates our SUPERflex™-12 pipe, making installation easy even on the coldest of days on site.

Learn more